WARNING: Please be sure to back up data and get a new hard disk. A failure may be predicted to the extent that it is likely to lead to unpredictable failure.
This kind of warning message makes it very clear that BIOS is asking you to replace your hard disk with a new one. But some people complained that this message appears when there is no bad sector on their hard disk or it is a new one. In this case therefore, we might admit that this Warning may not always be true and may be elicited on other antecedents. In this guide, I will show you a few things that you must do if you want to back up data and replace HDD. Well then, let the discussion commence.
Resolution: “Please Back Up Your Data…” Error
| Situation | Solution |
| You get the warning message, and the computer starts right away without any problem. | Copy all your data to another external hard disk if possible as soon as you can.Please run CHKDSK /f to perform a disk check as well as to correct problems on the hard disk.These two possible solutions: try to restart your PC, and if the problem continues to show the message, replace your hard disk. |
| This is the warning message you get, and as you try to boot to the Windows OS, it will not be possible. According to the steps stated above, follow the steps given below: Once on the Windows desktop: Proceed as in scenario 1. | Be sure to run Startup Repair and then restart your computer to determine whether you have access to the Windows OS.Turn off the SMART self-test and attempt to run the operating system of the desktop, Windows OS. |
| You need the files, and you are unable to boot the Windows operating system. | This can be done using the Windows Recovery Environment to backup files or folders. |
| You cannot load Windows or WINRE and have a second PC. | Connect the faulty disk to another PC.Update hard drive firmware. |
| Your disk is corrupted and does not run on a second computer. | Format hard disk drive. To resolve the issue, use Data Recovery Tool to retrieve your lost data. |
Run Chkdsk Repair HDD
Chkdsk command, a built-in application offered by Microsoft to all Windows users, scans, identifies, and repairs hard disk issues. If there is a little error on your hard disk, such as a few defective sectors, this tool can fix it and prevent you from receiving the warning message again.
Here are the steps:
1. Press Win + R to launch the RUN dialog box and type “cmd.”
2. Press Ctrl + Shift + Enter to open the Command Prompt in admin mode.
3. Type “chkdsk e: /f /r /x” followed by the Enter key.
Note: The “e:” is the drive letter where Windows has been installed.
4. Restart the PC and check if you still receive warning message.
Activate Startup Repair
Startup Repair is an inbuilt feature of Windows that helps to diagnose and repair the issues that can stop your PC from starting normally. It’s particularly helpful if you are having boot problems, including the case where Windows doesn’t start or freezes during booting. The Startup Repair tool is available in the Windows Recovery Environment; hence, to start it, you need to restart your PC and press F11 key until you get to WINRE.
After loading PC wake up WINRE click on Troubleshoot, then under the selection of Advanced Options, click on Startup Repair, and go through the steps to check and fix your computer’s problems. The PC will start normally after the repair has been done.
Disable SMART Self-Test
If Startup Repair won’t fix the problem, you can disable the SMART Self-Test so that Windows will start up so that files and folders can be copied. The method of disabling the SMART Self-Test depends on your computer’s BIOS. These guidelines vary depending on the model of the PC; thus, those who want to know more should visit the website belonging to the manufacturer of the PC.
After disabling the SMART Self-Test, you can log into the Windows operating system normally and backup all files and folders. After that, you can replace the hard disk. It is not suggested to always turn off the SMART self-test; thus, you may need to replace the hard disk.
Take Back Up Data and Replace HDD Using Windows Recovery Environment
If you are unable to get into Windows, you can copy your files and directories with the Windows Recovery Environment. First, go to the Advanced Startup Options screen, then Troubleshoot > Command Prompt. Once the Command Prompt window appears, type “Notepad” and press Enter.
The command above will start the Notepad application in the Windows Recovery Environment. Next, click Ctrl+O to display all of your hard disks, partitions, and external devices attached to your computer. Open the afflicted drive and copy the data. Then, transfer the data to a separate storage device. This process may take some time, but it will allow you to backup your stuff.
Know about the types of BSOD errors
Change PC And Connect Hard Drive Again
For this, you must have a second computer. You need to take off the hard drive that has problems by opening the computer case. Locate free Hard Disk Drive connectors on the motherboard. If there are none, connect the drive via an external hard disk casing. Once the detect has been done, then you can make your data backup.
In most cases, a bad hard disk could not startloading the Windows OS, but it will work as a second hard disk. As such, you can link it with another PC and transfer all the necessary files to this drive.
Update Firmware
An early version of firmware on a hard drive can possibly cause this error to occur. For instance, even on a sound hard disk the firmware may be out of date. The solution to the problem is to download the latest firmware on another PC and to install the drive in your computer. For the specifics on how to update the firmware on your hard drive, consult the firm’s website.
Format Hard Disk
To format your hard disk, connect it to another PC using one of the USB ports, then open this PC. Go to My Computer, right-click on the affected hard disk and click format, all connected hard disks will be shown. If you follow the above steps, you’ll find that your hard disk will be formatted. In your case, if you do not have a second PC, then the only way to repair your Windows is by using the Windows installation disk and format and reinstalling Windows on your Hard Disk.
Recover Data Using Professional Data Recovery Tool
Many users are getting the error “Backup your data and replace HDD.” Now we come to know why we are getting this error, but this is not the solution to the problem. The solution that everyone is looking for is mentioned here. There are so many tools/software available on the market that claim to recover data from corrupted hard disk drives. But which tool is suitable for your needs? You might have questioned yourself: Will this tool be able to recover your data? Well, we have tried a few of the tools and software that are available in the market, and these tools are based on user reviews of software and expert suggestions. Different users have different needs and their reviews help other users to select from the list of software. So, all the software that is mentioned is based on user reviews.
I am choosing the top 5 professional Data Recover Tools:
1. Easeus: (3.8/5)
2. Recuva: (3.9/5)
3. BLR Tools: (4.8/5)
4. Stellar: (3.9/5)
5. Wondershare: (3.7/5)
Error Back Up Data and Replace HDD – Is It Gone?
I think these solutions help to fix “Warning: Back Up Data and Replace HDD” issue. If all your files have been restored, you may want to replace the hard disk or replace the copy of the Windows OS. Please use the comments section below to share with us your issue we would love to solve your issues.